Which cat5 wires for phone

Your telephone is a device that you can connect to your router , sending your voice signal from your telephone into a digital signal that travels over the Internet. You can connect your router and phone in only a few minutes.

Connect your phone to your router in a few minutes. Ethernet network cables are typically used to interconnect computers and network devices such as hubs, switches and routers. Cat 5 cable and RJ jacks have eight wires. Ethernet uses two pairs four wires , one for send and one for receive. Telephones use two wires. Therefore, you can run both ethernet and telephone over the same wire, and still have two wires left over.

Can you hook up Internet through a phone line? DSL is a very high-speed connection that uses the same wires as a regular telephone line. If you find a break, it is acceptable to solder it to fix it-- phone is not as high-quality as ethernet. A multimeter may be helpful here. Afterwards, check that your wires are attached to the proper place on the jack. One wire should go to the red terminal, and one to the green terminal. Do not confuse the green terminal with the solid green Cat 5 wire. Finally, check that your wires are the same on both ends-- that is, brown striped to red, solid to green.

Most likely it is a different problem, as long as you were diligent enough to double-check all the orientations. Power over Ethernet is a technology that allows ethernet devices such as access points to operate without the need for wall power. It is not used widely except in businesses. Since you disconnect one of these pairs using this method, PoE will simply stop working it is not dangerous to use PoE devices, the wires are simply disconnected. If you desperately need to use a low-power PoE device, you may get around this by only using one wire from each pair for phone.

One example of this would be the striped brown wire and the striped blue wire. Then, the solid brown wire and solid blue wire would continue to work for PoE. However, this halves the maximum current that the cable can handle and may present a fire hazard when using large power-hungry devices. I do not recommend this, but it is a possibility.

Question 5 months ago. All of the bedrooms in my house have wall plates with RJ45 outlet. Currently we have cable internet and a phone landline. I would like to change some of the bedrooms to hard wire Ethernet internet connection. The photo is the current setup. This is my plan and can you please let me know if this will work or not? Disconnect the green cables for the rooms that I want to have hard wired internet and add RJ45 connectors to them.

Plug them into a multiport switch. Plug the internet cable to the modem and the multiport switch to the modem. Now would all the rooms that are hard wired be ready for hard wired connection and also able to have wireless access points there?

AC for advanced users 5. Reply 3 years ago. Gigabit requires Cat5e. Cat5 MHz doesn't have the bandwidth to sustain the gigabit signaling rate MHz. Rather than hack apart your wires in the wall, you can buy or build what's known as a "splitter. They're easily available to split the cable into two ethernet channels, or four phone channels. Making a custom one is as easy as doing what you did here with a short piece of cable and putting a plug on the end of it.

Keep the wires as close to their original configuration as possible to minimise the amount of interference you pick up. Read don't untwist the wires any more than absolutely necessary, and have them fork off from each other at the last possible moment. The advantage to doing it this way is that it's not permanent so you can reconfigure your panel any which way you want in the future.

I can probably be convinced to post an instructable about making splitters if anybody's interested. Reply 5 years ago. I'm also going to get exceedingly pedantic here.

An analog telephone requires RJ11 configuration, and as such has a 6P2C modular plug on the end of its cord. This was also used for digital PBX handsets that required separate pairs for power and signal. The handset connection on most phones is a 4P4C plug but is not used by any RJ definition. There are about a dozen other RJ specs that use the 8P8C modular connector RJ31X being very common for alarm panel connections in fact, your connection block above shows that as "line seizure.

How to Know whether it is Gigabit or ordinary cabling? Tip 3 years ago on Introduction. This is made possible because of the wasteful some may say "spare" wires in cat - 5 cable. Cat 5 cable and RJ jacks have eight wires. Ethernet uses two pairs four wires , one for send and one for receive.

Therefore, you can run both ethernet and telephone over the same wire, and still have two wires left over. Additionally, can I use Cat 6 cable for phone line? For traditional business telephones CAT5e is all that is needed. There would be no advantage to using CAT6 with a phone. It is recommended to keep the runs to or less when using patch cords. Telephone cable is one of the merits of a phone line network. You can connect a computer to the network in any room with a phone jack. Ethernet Cable.

Ethernet cable , also called Ethernet patch cable or network cable , is the most common type of cable used for home and enterprise network connectivity. You could have one phone connected to the blue pair, and a separate telephone connected to the brown pair, however. Use both wires in that pair.

Phil C Phil C 1, 1 1 gold badge 4 4 silver badges 17 17 bronze badges. Sign up or log in Sign up using Google. Sign up using Facebook. Sign up using Email and Password. Post as a guest Name. Email Required, but never shown. The Overflow Blog. Podcast Explaining the semiconductor shortage, and how it might end. Does ES6 make JavaScript frameworks obsolete?

Featured on Meta. Now live: A fully responsive profile.